• How do I manage my computer at home remotely?
• Which waveform to use in Rife, Sine, Square, Sawtooth, Inverse Sawtooth, Triangle, Damped Sinusoidal, Damped Square, H-Bomb Sinusoidal, H-Bomb Square?
• How to enter Gingerol and Shogaol Frequencies into Spooky2?
• Can Spooky2 combine it with Schumann frequencies? How to run Schumann frequencies on Spooky2? Is there a preset?
• I have Spooky Boost. When to use Inverse+Sync, Follow Out 1, Spike+Sync of Out 2?
• How to create a Spectrum sweep or Converge Sweep that targets the area Hulda Clark defined as where most pathogens live?
• What is Carrier sweep? Can Spooky create a custom Carrier Sweep and Modulation Sweeps?
• What is the recommended amplitude setting for both remote and contact mode treatment?
• I wondering why the immunomodulator preset isn't in the latest presets.
• Can you put in a shorter bacterial spectrum sweep that covers all bacterial pathogens?
• What is the best JW preset to use either the "Spooky Converge Sweep" or "Spooky Spectrum Sweep" if my intention is to treat as many pathogens at the same time as possible? I want to run for shorter time frames and manage die-off in stages.
• I see there are 2 channels running. "Out 1" (Square H-Bomb) and "Out 2" (Inverse+Sync) are different in the software green box and also directly on the LED display of the generator. I only got 1 magnet connected. What is happening with CH2?
• Restarted spooky2 and immediately got a message saying "No Generators detected." Exit and Install drivers. I checked the cables multiple times, restarted the computer and tried spooky2 on a different laptop. The USB cable looks fine.
• How to create a program?
• I think I am missing another healing frequency database. I remember I saw somewhere the Aruvedic frequencies that I can't find in November 1st. database. Am I missing something or it's there? Please respond.
• Why do I not have any DH killing/healing options in my Program Preset? I only have JW.
• What does the Hz gate setting do?
• Do I enter frequencies from Char. B. the same as frequencies that are listed in the database? In other words is there anything special I need to do as far as presets or anything like this?
• I am trying to run the Protomxzoa Sweep and the instructions are not matching the changes in spooky. Out 2=Out 1x1+0 volt. The x1 is missing with the software changes. How do I now get the correct settings.
• How do I link my email with my spooky2 channel data so I can send emails on the spooky protocols and frequencies I am sending to the generator where there DNA is "assigned".
• I have some question about turning your XM generator into 2 generators. How can I do this with SC?
• I have some question about turning your XM generator into 2 generators. Can I use 2 different presets, one in out 1 and another in out 2?
• I have some question about turning your XM generator into 2 generators. Do I need a remote in out 1 as well as out 2?
• Could someone please post a step by step method with perhaps a screenshot of the settings used to go beyond the 5Mhz limit capability of the 5Mhz generator unit?
• Is there a way to make sure that a program (that is already running) has been set correctly for channel overwrites. i.e. that "Allow Channel Overwrites" and "Everytime" were both checked?
• How to achieve pulsed 10 Hz?
• Is this bad for the generator to not have something connected to OUT 2?
• How to create a frequency set? I go into "database" , "edit database". I note for example 100 W2 O00 A02, 200, 300, Invalid file; I try 100 = 180.200 = 180, idem.
• How large of hard drive do I need on a laptop to run spooky 2?
• I copied the weight loss program, but I don't succeed to paste it in the users file. When I open the file and want to paste, the paste button is unavailable. What am I doing wrong?