- I would like to create a program with Amplitude 10v and make positive offset 100%. Can this be done and executed with XM Generators through the Spooky2 software?
- Under what program should a molecular substance do? If I use EOs under the healing program and aspartame under detox?
- Is there anything I need to do before imprinting water to make it more effective?
- Do I need to apply tissue factor when I am using the presets under Environmental tab in contact mode?
- Why these empty shell presets are empty?
- When creating programs on healing or killing they should be about a 4 hour run time? Can you run 4 custom created programs at once for about 12-13 hours straight?
- Given I only need one for 11 says, can I turn off the second Generator manually without causing any damage? Or should I shut everything down and start over with just one generator turned on?
- Regarding preset of miscellaneous > remote > eczema (JK). Is it the same to run that preset and to run empty shell > H bomb - and then run eczema 2 (XTRA)? How to make a custom set including that preset?
- Here not individual frequencies are taken, but the decades (x * 1 - x*10 - x*100...). So when 45 was needed, you had the decades of 45 (45*1 - 45*10 - 45 *100 ...) and not only 45 Hz alone. Is it possible to create corresponding programs with Spooky2?
- How many "hits" is recommended to keep for use from the list of results?
- Why I’m running GX BFB with nothing connected still showing hits? Is there a way to calibrate?
- How can I run a single square wave sweep from 500Hz to 25KHz that completes in 2 hours with Spooky2-XM? How do I set? I will be using it to drive my plasma rig.
- How to get into the pharmaceutical database? I did the advance, empty shell, to programs, typed in the drug and nothing came up. Also there is no update database button on the database just refresh is that the same as updating database?
- Is the H Square Bomb preset as effective as a killing or healing preset and is there any advantage of using it if I know which is a killing or healing program?
- What does the Chakra system frequency do in the spooky2?
- Can I use the Chakra programs with Eczema preset because the Eczema preset is a killing preset and the Chakra is a healing preset? What should I be in it if I want a good memory?
- While running Terain detox preset, Spooky2 software is running fine but the generator says it is off and the remote lights are not on. The generator has the current frequency showing, so what’s wrong?
- My GX biofeedback scans show either only a couple of hits or hits with very low scores (less than 1.0). It is recommended to either change the threshold to 0 or to change the type of scan to 'current and angle', which should I choose?
- Why my Spooky2 keeps freezing on Windows 10? There's been a few times now when I go home I find windows 10 has killed spooky and it’s asleep, or Spooky2 has frozen. I already have my sleep settings set up according to the directions.
- What is the difference between analyse button and analyse + button?
- How to chain the Tinnitus healing program and Detox program.
- Does anyone know how I can move my scans from one computer to the next?
- Can someone explain this waveform area to me?
- In the "Terrain minus mercury" I see that the first few steps still remove other metals. How would I like to skip the metals entirely for now?
- When I save custom programs and scan results in the software, where do they get saved in? Will they be saved as documents? How can I load them?
- I have watched several Spooky videos, made notes on how to chain presets, and I am still confused. Where are these instructions on Spooky website. Or has anyone compiled instructions that work?
- How to make a custom frequency program file that's really just the frequencies in an existing preset with a couple more frequencies added on. Instead of making a custom file. Can I just add frequencies to an existing preset?
- Is there a way to see this whole chart once it is finished? And how are people interpreting this chart?
- Where does one find the software with the ‘Advance’ button for running Biofeedback in Gen x which I see on YouTube videos? I have the latest 201811 software but No Advance button.
- Currently doing colloidal silver, some number in Control tab under generator output change to red. The frequency and amplitude change. What does this mean? Please refer to the photo.
Help Center
