- Can you chain 2 or 3 presets and they repeat infinity? I know if we mess with the schedule then that preset when its done will not cycle to next preset. So is there another way?
- What is this "original DH1" in the preset "kill or heal DH"? Can I use this preset with basic rig (remote and BN)? Otherwise I can use the killing preset for these programs?
- I would like to use the new presets from Newport, which is a chained preset. But it stops once it is finished. Is there a way to keep looping the preset chain nonstop?
- What does Wdb5 mean in the program descriptions? It's in a lot of the programs I want to use. Is it a special preset waveform or something that needs to be set if using that program?
- What is 'cancer spectrum sweep', and can it stay launched without time limits (as kind of cancer prevention)? What is the principle of 'immune system stimulation', is it the same way as bob beck zapper?
- For program "Calcium Fluoride CaF2 (MW)", do I have to use option "Apply Tissue Factor to MW and BP Program". Do I have to use the "Healing" preset? Should I use the "Golden Ratio" preset?
- The software stopped working, so I decided to reinstall. The message “mscomctl.OCX” came up when I tried to open the software. So I reinstalled again and the same thing has happened.
- I’m building a custom database around efficacious frequencies. When I open the the frequencies Zip folder, it is empty. What should I do if I want to cut and paste all the frequencies I want?
- I had a hard time figuring out how to run a program. I ran the eyes under a heal preset and I ran the athletes foot under a general killing preset. Should I have run athletes foot under a healing preset?
- When I try to install Spooky2, I keep getting this error message that is Run-time Error 8002. What am I not thinking of?
- Is there a difference between Spooky2 Starter Pack and Spooky2 4 February 2017 Full Installer? Which of the link should I download?
- How to Install and Use Chain Editor?
- What is Preset Chain?
- How to use load programs?
- Why aren’t the running frequencies within the Limits set given in the Settings?
- What is that golden ratio used for? How does it help us then?
- Currently experimenting with HC frequencies and trying to find ways to enhance them. I’ve added the a frequency multiplier(11th), a harmonic wobble(+- .02% Feathering). I’ve been messing around trying to add spikes into the square wave.
- After updating to the newest version of Spooky, I no longer see my previous biofeedback results. Do I need to do something special to bring these frequencies back into spooky?
- If I want to make sure the programs I select only run for a maximum of 4 hours, where do I make the adjustments/change settings?
- When I choose empty shell preset/ kill or heal(R) -DH, the offset of out 1 is 100 and out 2 is -100 % is that ok?
- How many of you choose different waveforms for out 1 v. out 2, when creating your frequency sets? What is the benefit to doing so?
- The guide recommends spike length of 1 or 2, depending on the frequencies used. What are the pros and cons of a spike length of 4? The only mention of higher spike lengths in the the guide says: a Spike Length of 24 as shown wouldn’t be a good value.
- If I have a frequency for killing, lets say 123 that I need to sweep plus minus 10 Hz, do I just create a new program and enter 113-133 and then let it run, or do I need to use any special settings like those from spectrum sweeps or other?
- I do not understand how to use the "Loaded programs" box.
- I have found that running frequencies for 3 minutes(Dwell set at 1) on Remote is often too much. Currently I have the Dwell set at .05 which gives 9 seconds of treatment for each frequency running. Is this ok?
- I downloaded the latest 2/4/17 software on all of them. In looking at the MW database on the computer that is connected to the generators, we saw that there were only 260 there.
- Since updating from Dec 16 to Feb 4, I can't use disintegrate factor in MW database? It doesn't have the tick box anymore?
- When running a program, am I supposed to change all kinds of settings (wave form, harmonic scale, etc) every single time to make it actually work, or optimized? Or do the programs already have these things taken care of for us?
- I noticed that there was no place to put the target cancer program in the latest Feb. DB Cancer protocol.
- Why is it important to keep your Spooky2 software up to date with the latest install?
Help Center
