- I am running some programs loaded in an empty shell via remote mode to treat gall stones using Gen X. But I forgot to write the names of the programs for further reference. Now what should I do to know the names of the programs.
- Can I program my own square waves? Not simple but rather things like 1,1,1,0,1,0 repeated at the fundamental frequency.
- I’m running autoimmune disorders and wondering if I should use killing or healing preset.
- Basically I ran Terrain according to the instructions, it says to check the 'Allow Generator Overwrites' Box. Which I did. But as I am looking at the Control Tab now I see that this 'Allow Generator Overwrites' box has somehow unchecked itself.
- I have done the biofeedback scan and saved it. It's in the program description but how do I get it in the loaded programs. Also do I click the killing preset? Do you put a finger nail in the remote too?
- How do I know which program is running on which generator?
- I have created a program of high frequency hits using GX and Sample Digitizer. I want to run this program using a remote killing preset on my XM generators. What changes do I have to make in order for the XMs to be able to produce these higher frequencies
- Why isn't a sine waveform used instead for healing and regeneration preset rather than square wave? For what I know, sine waveform is usually used for healing while square wave is used for killing.
- I’ve just finished the terrain detox on remote. How do I now get rid of it? Tried a few things thought it was gone. Loaded some programs to run and when I click my generator it just starts the terrain again.
- When will a preset be available to download in the program menu?
- How can I download C60 & install it in my programs on Spooky2?
- How to schedule your presets using preset chain?
- I wonder how to remove old programs that we created from the BFB? If we run the BFB daily we keep a large number of unnecessary data. I would like to keep only most relevant scans.
- How do you delete old and unwanted BFB scan results?
- I did a sample digitizer on my blood and generated some frequencies. I set up a contact program to run these frequencies on my Spooky 5-XM generator. The frequency that is showing up in the software is an octave of the one found. Why is that?
- Is there a way to set a different duty cycle for output 1 and output 2?
- How is threshold calculated?
- Is there an easy way to edit a biofeedback program once it's saved and appearing under the programs tab as a BFB program?
- Can someone help me with saving scan results to a flash drive so that I can transfer to my other computer.
- I have been running programs to remote via Spooky2 XM. Do programs just stop after a lot of time via the computer? Is there a way to make the programs loop around and keep repeating?
- Why would trying to load a BFB file (to analyze) bring up the error message, “run-time error ‘62’?” What can I do to fix this?
- I know that in the settings for a biofeedback scan Max search for killing frequencies and Min for healing frequencies. But what is the difference between BPM and HRV by the scan results? And Change on or off?
- If I’m running the Detox terrain program, once it’s loaded does it just run for the 11 days automatically changes or do I have to Monitor and change daily?
- I have two generators that generate a different program in AM "Modulate Out1". The ratio of subsequent frequencies between generators is Gen1/ Gen2 = GoldenRatio. How to run Programs on different generators simultaneously or how to synchronize them?
- I am using the Cancer Advanced (R) JW Preset which uses a sine waveform. I would like to add to this a set for Urological Neoplasms. Does the Advanced Preset also take those frequencies higher? Can I change the waveform to an Square H Bomb?
- I am just getting familiar with Spooky 2 Starter’s kit. I have one program going 'maintenance detox remote.' I do not know how to switch that out and put in another program.
- I use the latest software 20180401 and renamed the prior version to preserve my BFB scans. I copied the BFB scans from prior version to new ScanData folder, but they don’t come up in the program search BFB. How can I use BFB scans from prior software?
- Is there a way I can tell the system to wobble 10 Hz below and 10 Hz above EVERY frequency in a list without creating over or under wobbling?
- What does KHZ mean, does it meam kilo hz?
- I did the detox preset Terrain Protocol. And after the 11 days it started all over again by itself. How can I tell spooky2 that I do not want this looping?
Help Center
