- Is anyone experiencing this 'Error in Database' c:\Spook2\MW_Frequencies.zip has the invalid line followed by unreadable characters?
- I'm experimenting with the Golden Ratio. Software says sync is off on the computer, yet it is checked in the 2nd column for invert the spiked waveform. Is this correct? Just checking cause I have to manual set the sync on generator always, old generator.
- In KHZ Contact preset, it says recommended starting point is Square wave, 100% positive Offset, and Amplitude of 9.5. If you change to inverted sawtooth does the offset of 100% stay the same? Similarly what about changing to Square H-Bomb and wobble?
- Can I use at the same time the 11th harmonic (page 65 in the user's guide) and the very high frequency explained on page 67? I get the photo below:
- How can I create 13.5 MHz carrier wave?
- Is it OK to use the Holland 11th harmonic effect for both killing and healing? Should I set the amplitude on 20V when using KHZ sets?
- How to quickly find your custom database in the programs tab?
- If I can replicate near infrared freq. e.g. 850nm (0.85 micrometers) and 890nm (0.89 micrometers) or higher with the generator? Can I program the generator to produce these?
- I can't find a way to use SC without Modulation or Carrier.
- What is the difference between using a preset for sweeps and when a sweep in a healing or killing program. With those programs do we need to use any specific preset?
- What's the difference between presets and programs?
- I have a question about the remote mode. I have been running two programs all night they are 1:24 duration, when I woke up this morning it says current duration time 2:53 even though it has been running for about 12 hours now, how can interpret this?
- How to Perform a Reverse Lookup after a Biofeedback Scan-Silent Movie Version
- How to Resume Terrain Protocol after Restarting Software and Generators-Silent Movie Version
- How to Perform a Quick Scan (Grade Program)-Example-Silent Movie Version
- 10-21-16 Spooky2-Terrain Protocol(Remote)-Time-Lapse Video-Silent Movie
- How to Navigate the Spooky2 User's Guide? Create a Remote Program- Example -Silent Movie
- How to Load Drivers and Perform Signal Test - Spooky2?
- How to Modify the Power Settings and Windows Update Settings in Windows 7?
- How to Install the Molecular Weight Database? (dated 8 27 16) - (Free)
- How to Install the 10-21-16 Spooky 2 Software? (Free)
- How to Unzip the 10-21-16 Spooky2 Zipped Folders (Free) in Windows 7?
- How to Download the 10-21-16 Spooky2 Software and User's Guide? (Free)-(Zip Folders)
- Oct 21, 2016 Spooky2 Software (Free) - Brief Introduction - Features - Test Mode
- The preset for sleep/insomnia seems to be run continually for 24 hours for 12 to 24 days? I would think it should only be run before and during bedtime?
- Is it better to make a preset by preset chains and run, or instead, to run the presets simultaneously on separate generators?
- When the Settings tab reads Amplitude: Output 1: 20v, Output 2: 20v. You are using a boost, does that mean you are getting: Output 1: 40v, Output 2: 40v. Does the computer program recognize that the "boost" is being used, thus doubling the voltage?
- I noticed in the Settings tab it set Out1 to a Square wave with Inverse+Sync selected. The notes for the KHZ preset say Square wave, 100% positive Offset, and Amplitude of 9.5. Should the Waveform be set to Follow Out 1 or left at Inverse+Sync?
- How long to run environmental presets?
- How to manage/edit a users database in my software interface?
Help Center
